Production Engineering Quiz | Production Engineering Objective Type Questions & Answers

Sports GK Questions and Answers 2024 (Latest Updated)

Awards & Honours GK Questions 2024 (Latest Updated)

Questions
21 Sprue in casting refers to
A Vertical passage
B Riser
C Gate
D Runner

Answer: Vertical passage
22 Which of the following operation is first performed?
A Boring
B Drilling
C Spot facing
D Tapping

Answer: Boring
Advertisement
Article and Schedule Quiz Start Test!
DOWNLOAD CURRENT AFFAIRS PDF FROM APP
23 The casting defect caused by the erosion of sand
A Misrun
B Drop
C Wash
D Rat tail

Answer: Drop
24 Ceramic cutting tools are
A Brittle and have low bending strength
B Available in the form of tips
C Made by cold pressing of aluminium oxide powder
D All of these

Answer: All of these
25 Which of the following gating ratio represents pressurized gating systems?
A 1 : 1: 2
B 1 : 2 : 1
C 1 : 2 : 3
D 1 : 3 : 3

Answer: 1 : 2 : 1
26 In a shaper, the length of stroke is increased by
A Increasing the centre distance of bull gear and crank pin
B Decreasing the centre distance of bull gear and crank pin
C Increasing the length of the arm
D Decreasing the length of the slot in the slotted lever

Answer: Increasing the centre distance of bull gear and crank pin
27 Most commonly used materials cast by using hot-chamber die casting include
A Lead
B Tin
C Zinc
D All of these

Answer: All of these
28 Spot facing is
A Localised machining of a component
B Machining of a spot to fit other parts
C Mahining of spol on the surface of a part to furnish a flat bearing or the head of a holt or nut
D A spot prepared on shaper or milling machine

Answer: Mahining of spol on the surface of a part to furnish a flat bearing or the head of a holt or nut
29 A shim is
A A treatment given to a surface to prevent rusting
B A dull corner on a shaft
C A thin piece of sheet metal used between mating parts to provide the proper distance
D A surface on which bearings are fitted

Answer: A thin piece of sheet metal used between mating parts to provide the proper distance
30 Quill is
A A tool used in milling machine to cut T-slots
B A holding device used on planers
C Curring a blind key way on an object
D A steel tube in the head of some machine tools that encloses the bearings and rotating spindle on which are mounted the cutting tools

Answer: A steel tube in the head of some machine tools that encloses the bearings and rotating spindle on which are mounted the cutting tools
31 Necking is
A Machining a groove around cylindrical shaft
B Drilling a hole in a plate
C Hole drilled for riveting
D Preparation of surface for brazing

Answer: Machining a groove around cylindrical shaft
32 Burr is
A Unmachined portion of work piece
B Boundary between finished and unifinished portion on a work piece
C A marking or work piece to identify for correct position on a work piece
D Sharp edge remaining on the metal after curring, stamping or machining

Answer: Sharp edge remaining on the metal after curring, stamping or machining
33 Buffing is
A A process of electroplating
B Covering a metal part with soft materials to prevent damage
C An finishing operation in broaching
D The process of bringing out the luster of metal

Answer: The process of bringing out the luster of metal
34 Angle plate is
A Used for holding angular jobs in milling machine.
B Used for cutting angles on jobs on shaper
C Cast iron jig used to hold work in a vertical position of layout or machining
D Used for measurement of angles

Answer: Used for measurement of angles
35 The size of a lathe is expressed by
A Gross weight of lathe
B Diameter of chuck
C Maximum speed of chuck
D Swing of lathe

Answer: Swing of lathe
36 Magna flux is
A A non-destructive inspection technique that makes use of magnetic field and magnetic particles to locate flaw in materials
B An instrument using ultrasonic techniques for crack detection
C An instrument used for inspection of weldings
D An instrument used for precision measurements using magnetism and flux density

Answer: A non-destructive inspection technique that makes use of magnetic field and magnetic particles to locate flaw in materials
37 A half nut is
A Damaged nut
B Nut manufactured in parts
C Nut with half the standard pitch
D Mechanism that locks the lathe carriage to the lead screw for thread cutting

Answer: Mechanism that locks the lathe carriage to the lead screw for thread cutting
38 Gang milling is
A Process of cutting gears
B Milling process for generating hexagonal surfaces
C Process in which two or more cutters are used simultangeously
D High speed milling

Answer: Process in which two or more cutters are used simultangeously
39 A flycutter is used on
A Lathe
B Shaper
C Milling machine
D Slotter

Answer: Milling machine
40 Lathe bed is made of
A Mild steel
B Cast steel
C Pig iron
D Close grain cast iron

Answer: Close grain cast iron

Random GK Questions

Q. Literal meaning of the term Homo Sapiens is
Q. Which Part of the Indian Constitution is associated with Citizenship ?
Q. Point out which one of the following sites has yielded the remains of a Jaina stupa ?
Q. During the Mughal period which one of the following traders first came to India?
Q. Which of the following food items is rich in iron?
Q. blowouts are the formation of
Assam Direct Recruitment Test Series

Teacher Eligibility Test

Assam Direct Recruitment Test Series