Workshop Technology Quiz | Workshop Technology Short Questions and Answers

Sports GK Questions and Answers 2024 (Latest Updated)

Awards & Honours GK Questions 2024 (Latest Updated)

Questions
41 The metal patterns as compared to wooden patterns require less
A Shrinkage allowance
B Machining allowance
C Draft allowance
D Distortion allowance

Answer: Draft allowance
42 According to Indian standards, the total numbers of tolerance grades are
A 8
B 12
C 18
D 20

Answer: 18
Advertisement
Article and Schedule Quiz Start Test!
DOWNLOAD CURRENT AFFAIRS PDF FROM APP
43 The chisel used for cutting key ways is
A Flat chisel
B Cape chisel
C Round nose chisel
D Diamond pointed chisel

Answer: Cape chisel
44 Lancing is the operation of
A Cutting a sheet of metal in a straight line along the length
B Removal of metal to the desired shape from the edge of a plate
C Cutting a sheet of metal through part of its length and then bending the cut portion
D Bending a sheet of metal along a curved axis

Answer: Cutting a sheet of metal through part of its length and then bending the cut portion
45 When the molten metal is fed in the cavity of a metallic mould by gravity, the method of casting is known as
A Die casting method
B Slush casting method
C Permanent mould casting method
D Centrifugal casting method

Answer: Permanent mould casting method
46 The welding process used in joining mild steel shanks to high speed drills, is
A Spot welding
B Seam welding
C Flash butt welding
D Upset butt welding

Answer: Flash butt welding
47 Which one of the following material will require the largest size of riser for the same size of casting?
A Aluminium
B Cast iron
C Steel
D Copper

Answer: Steel
48 The advantage of Thermit welding is that
A All parts of the weld section are molten at the same time
B Weld cools almost uniformly
C Results in a minimum problem with internal residual stresses
D All of the above

Answer: All of the above
49 Loam sand is a mixture of
A 30% sand and 70% clay
B 50% sand and 50% clay
C 70% sand and 30% clay
D 90% sand and 10% clay

Answer: 50% sand and 50% clay
50 The teeth of hacksaw blade are bent
A Towards right
B Towards left
C Alternately towards right and left and every third or fourth left straight
D May be bent in any direction

Answer: Alternately towards right and left and every third or fourth left straight
51 Structural sections such as rails, angles, I-beams are made by
A Hot rolling
B Hot drawing
C Hot piercing
D Hot extrusion

Answer: Hot rolling
52 Metal patterns are used for
A Small castings
B Large castings
C Complicated castings
D Large scale production of castings

Answer: Large scale production of castings
53 When more volume of acetylene and less volume of oxygen is supplied, then a ________ flame is obtained.
A Neutral
B Oxidizing
C Carburising
D None of these

Answer: Carburising
54 The process of decreasing the cross-section of a bar and increasing its length, is called
A Drawing down
B Upsetting
C Spinning
D Peening

Answer: Drawing down
55 Cutting and forming operations can be performed in a single operation in a
A Simple die
B Progressive die
C Compound die
D Combination die

Answer: Combination die
56 In a cold chamber die casting machine
A Melting pot is separate from the machine
B Melting pot is an integral part of the machine
C Melting pot may have any location
D Low temperature and pressure is used

Answer: Melting pot is separate from the machine
57 Seam welding is best adopted for metal thickness ranging from
A 0.025 to 3 mm
B 3 to 5 mm
C 5 to 8 mm
D 8 to 10 mm

Answer: 0.025 to 3 mm
58 In order to check the clearance between two mating surfaces, a ________ gauge should be used.
A Ring
B Plug
C Feeler
D None of these

Answer: Feeler
59 The hot working of metals is carried out
A At the recrystallisation temperature
B Below the recrystallisation temperature
C Above the recrystallisation temperature
D At any temperature

Answer: Above the recrystallisation temperature
60 In blanking operation, the clearance is provided on
A Punch
B Die
C Half on the punch and half on the die
D Either on punch or die depending upon designer's choice

Answer: Punch

Random GK Questions

Q. Name the two non-permanent Houses in the Parliamentary set up of India?
Q. Yardang are a creation of
Q. Which one of the following type of microorganisms is most widely used in industries?
Q. The headquarters of OPEC is located at
Q. Citric acid is present in free form in
Q. The best means of saving during inflation is to keep:
Assam Direct Recruitment Test Series

Teacher Eligibility Test

Assam Direct Recruitment Test Series