Download PDF
Free download in PDF Manual Testing Objective Type Questions and Answers for competitive exams. These short objective type questions with answers are very important for Board exams as well as competitive exams. These short solved questions or quizzes are provided by Gkseries.
(21)
Which of the following is not a major task of Exit criteria?
[A]
Logging the outcome of test execution.
[B]
Writing a test summary report for stakeholders.
[C]
Assessing if more tests are needed.
[D]
Checking test logs against the exit criteria specified in test planning.
Answer: Logging the outcome of test execution.
(22)
Which is the odd one out?
[A]
Client or development side
[B]
Client side
[C]
Beta release
[D]
Beta testing
Answer: Client or development side
(23)
______ is an existing defect that has not yet caused a failure because the conditions that is required to invoke the defect is not meet.
[A]
Latent defect
[B]
Masked defect
[C]
Both of these
[D]
None of these
(24)
Top-down Design does not require ______ .
[A]
Loop-invariants
[B]
Modularity
[C]
Flow charting
[D]
Flow charting
(25)
Which testing cannot be performed by QA Team?
[A]
Fuzz Testing
[B]
Destructive Testing
[C]
End-to-end Testing
[D]
Equivalence Partitioning Testing
(26)
STLC is related to which model?
[A]
Spiral Model
[B]
V Model
[C]
RAD Model
[D]
Waterfall Model
(27)
Defects can be found more easily in ________ .
[A]
Top down Integration Testing
[B]
Bottom up Integration Testing
[C]
Sandwich Integration Testing
[D]
Big Bang Testing.
Answer: Bottom up Integration Testing
(28)
Focus Testing comes under ______.
[A]
Usability Testing
[B]
Component Testing
[C]
Acceptance Testing
[D]
Performance Testing
Answer: Usability Testing
(29)
Which is not true in case of Unit Testing?
[A]
It is usually conducted by the development team.
[B]
In this tester evaluates if individual units of source code are fit for use.
[C]
It decreases the software development speed
[D]
It can’t be expected to catch every error in a program.
Answer: It decreases the software development speed
(30)
Which of the following is / are not a Iterative Model?
[A]
V model
[B]
Spiral Model
[C]
Incremental
[D]
RAD
31
____________ is done by suddenly increasing the load for a small period of time and observing the behavior of the system.
[A]
Spike Testing
[B]
Load Testing
[C]
Stress Testing
[D]
All of these
32
Test plans are based on _______.
[A]
Support Plan
[B]
Business Plan
[C]
Project Plan
[D]
33
33
Which is not a part of Decision Table?
[A]
Driver portion
[B]
Action portion
[C]
Condition portion
[D]
Stub portion
34
Component Drivers are not needed for ______.
[A]
Top Down
[B]
Modified Top Down
[C]
Big-Bang
[D]
Modified Sandwich
35
Coupling and Cohesion is explained by _______ .
[A]
Cause-Effect Graph
[B]
Dependency Matrix
[C]
Structure Graph
[D]
Software Requirement Specification
Answer: Cause-Effect Graph
36
Which is not true in case of Sanity Testing?
[A]
Sanity testing is High Level Testing.
[B]
Sanity testing is a cursory testing.
[C]
Sanity test is usually unscripted.
[D]
Sanity test is a narrow regression testing.
Answer: Sanity testing is High Level Testing.
37
Confidence Testing refers to ________.
[A]
Regression Testing
[B]
Retesting
[C]
Smoke Testing
[D]
None of the above
38
Which of the following is / are not part of Specification Based Testing?
[A]
Data Flow
[B]
Boundary Value Analysis
[C]
Decision Table
[D]
State Transition
39
Which testing application security has the purpose to prevent problems which may affect the application integrity and stability?
[A]
Fuzz Testing
[B]
Vulnerability Testing
[C]
Ramp Testing
[D]
Penetration Testing
Answer: Vulnerability Testing
40
What is the ratio of effort needed to fixing a defect in Requirement Phase, Design Phase, Coding Phase and Implementing Phase?
[A]
1:8:12:100
[B]
1:6:10:1000
[C]
1:4:7:10
[D]
1:10:100:1000
Please share this page